Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterSimonton Door Installation: The Boca Raton Owner’s Guide
Simonton door installation in Boca Raton typically runs $220 to $485 installed for hinge, roller, and weather-seal replacement work, and most single-panel jobs are done the same visit. We keep common Simonton replacement components on the truck, and if your part is one we carry, the truck rolls with everything needed to finish in one appointment. The way most Boca Raton owners discover a failing Simonton door is gradual: the door starts dragging on the track in June humidity, or the sweep leaves daylight showing at the corner, or the handle has to be pulled twice before the latch sets. By the time you notice, the part has usually been wearing for months.
Which Simonton Models This Applies To
We install replacement parts across the Simonton sliding patio door and hinged French door lines most common in Palm Beach County homes: the Reflections 5500 and 6500 series, the DaylightMax 7300 and 7500 lines, and the Madeira vinyl hinged doors. The compatibility gotcha with Simonton is the roller assembly. The 5500 series uses a 1-1/4 inch diameter tandem roller with a stamped steel housing, while the 6500 and up use a slightly taller carriage that sits on a different track profile. They look close enough to confuse at a glance, and a mismatched roller will either bind or drop the door slab a quarter inch, which throws off the strike alignment. The quick way to identify your model: look at the spacer bar inside the glass, or find the AAMA certification sticker on the top rail of the panel. If the sticker’s gone, we measure the roller housing and track profile before quoting.
On the OEM-versus-aftermarket question: Simonton’s factory rollers and hinge kits are solid, but the factory sweep on older Reflections doors degrades fast in salt air. We’ve installed thousands of feet of aftermarket Q-Lon and fin-seal replacements that hold up longer between Boca Raton’s ocean breeze and the afternoon rain cycle. We’ll quote both and tell you which one we’d put in our own house.
Signs Your Simonton Door Installation Is Failing
- Door drags or grabs on the track. The roller bearings are flat-spotted or the wheel has started to delaminate. South Florida humidity accelerates the wear; once the wheel stops rolling and starts sliding, it shaves the track profile.
- Draft or daylight at the bottom corner. The sweep has taken a compression set and no longer seals against the sill. You’ll feel it most on east-facing doors that catch the morning sea breeze off the Intracoastal.
- Handle needs two pulls to latch. The keeper on the jamb has shifted, or the mortise hardware in the panel has worked loose. In a coastal climate the panel and jamb expand at different rates, and the misalignment worsens through summer.
- Door panel sags to one side. On older 5500 series doors, the hinge screws back out over time because the frame reinforcement plate was never upgraded. This is a ten-minute fix if caught before the screw holes strip.
- Condensation inside the glass unit. The door’s insulated glass seal has failed. That’s a replacement situation, not just a parts swap, and it’s the single most common Simonton issue we see within ten miles of the ocean in Boca Raton.
Replacement Cost & What’s Included
For Boca Raton homeowners, we price Simonton door installation work by the part and the panel accessibility, not by the hour. A roller assembly swap on a ground-level sliding door runs $110 to $180 per panel. A hinge and sweep refresh on a hinged door runs $95 to $165 per door. Full hardware replacement including handle set, keeper, rollers, and a new sweep on a typical 6-foot slider runs $280 to $485. The range depends on whether the door needs minor shimming to true the panel, whether the track is still in spec, and whether the existing hardware is factory-original or a previous handyman’s retrofit.
Every quote is a line item on paper before we start: parts, labor, and any track or shim work broken out separately. Nothing gets added to the bill that wasn’t on the quote. The work is covered by our Done Right Promise, and if the part you’re replacing has existing manufacturer warranty remaining, we check and register it in writing before the truck leaves your driveway. That’s The Keystone Standard, and it applies to every Simonton job we run in Boca Raton.
DIY or Call Us?
A homeowner with a 4-in-1 screwdriver can safely tighten a loose handle set, clean the track, and check for visible roller flat spots. Those are honest checks you can do this afternoon. Where DIY goes wrong on Simonton doors is panel removal. A full glass slider panel weighs 95 to 140 pounds depending on model, and the panel has to be lifted clear of the track, tilted, and balanced while someone works the roller screws from underneath. One slip means cracked glass, a tweaked frame, or a damaged tile floor. If the door is off-square, forcing a new roller in without correcting the alignment just eats the new part and you’re back to square one in six weeks.
We’re the same people who measure, quote, and install. Call (561) 264-1337 and describe what the door is doing. If it’s a quick fix and we’re in your neighborhood, we’ll give you a straight answer and a price on the phone before anyone books a visit.
FAQs
In coastal Boca Raton, we see factory Simonton rollers last 8 to 12 years before the bearings flatten, and sweeps typically 4 to 6 years before the seal compresses. Homes within a mile of the Intracoastal or the beach run on the shorter end because salt air and persistent humidity age both the plastic and the metal components faster.
A roller with worn bearings can’t be rebuilt; the wheel and bearing are sealed as one assembly. A rubber sweep can sometimes be re-seated if it’s simply pulled loose from the extrusion, but if the material has taken a set or cracked, replacement is the honest fix. We’ll tell you which one applies when we look at the door. Call (561) 264-1337 and we’ll diagnose it over the phone.
Most single-door roller, sweep, or hinge replacements take 45 to 90 minutes once the truck is on site. If we need to true the panel or address minor frame alignment, figure another 30 to 45 minutes. It’s a one-visit job unless the glass unit itself has failed.
We carry the most common Simonton roller assemblies, hinge kits, sweeps, and handle sets for the 5500, 6500, 7300, and 7500 series on the truck, along with compatible aftermarket options from Q-Lon and other lines we trust. If your part is unusual or the model is older, we order it and return within a week. As an independent service provider, we are not affiliated with Simonton, but we have installed and matched their parts across Palm Beach County for years, alongside other lines like Andersen, and Pella.
Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving Boca Raton and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.