Mr-Glass Sliding & Patio Doors Nationwide | TruePane Windows & Doors

Mr-Glass Sliding & Patio Doors: The Boca Raton Owner’s Guide

If your Mr-Glass sliding or patio door is binding, leaking air, or refusing to roll, we stock the rollers, tracks, handles, locks, and weatherstripping to bring it back into service. Installed replacement parts for Mr-Glass doors in Boca Raton typically run $160 to $490 depending on whether it’s a roller set, a handle-lock assembly, or a full track rebuild, and we carry the common Mr-Glass sizes on the truck for same-visit work. Most homeowners discover the failure the same way: the door starts taking two hands to move, then it makes a sound like dragging a bucket of gravel, and then one morning it won’t latch.

Call (561) 264-1337

A sliding door doesn’t quit all at once. It gives you a month of warnings: a catch in the track, a handle that feels loose, a gap at the corner where the weatherstrip used to seat. Those warnings mean a $22 roller has been grinding against a $180 track long enough to do real damage. The sooner you address it, the smaller the bill.

Which Mr-Glass Models This Applies To

Mr-Glass sliding and patio doors turn up in a lot of Boca Raton homes built in the 1980s through the early 2000s, and the parts are model-specific in ways homeowners don’t expect. The most common frames we service in this market are the Mr-Glass 2000 and 4000 series aluminum sliders, plus the heavier weather-rated patio doors that show up in 1980s-era condos along Palmetto Park Road and in Boca Teeca.

The gotcha: Mr-Glass used at least three different roller body widths across the 2000 series alone. A roller from a 1992 door will not seat in a 1987 track, even when both frames measure 72 inches. The only reliable way to identify the part is to remove the door panel and read the roller housing, or check the glass etching in the corner of the panel for the series code. We measure every opening twice and match the part from the physical hardware, not from a photo, because a 1/16-inch difference in the roller housing means the door will never track square.

For Mr-Glass specifically, we recommend OEM-equivalent rollers with sealed stainless bearings over generic aftermarket units that use unsealed nylon wheels. The salt air in Boca Raton, especially east of I-95, eats unsealed bearings within two seasons. The few extra dollars on a sealed bearing buys you years of clean tracking.

We are an independent service provider and are not affiliated with Mr-Glass. We also stock compatible parts for PGT, CGI, and CWS sliding doors, so if your home has a mix of manufacturers, we can handle the whole project in one visit.

Signs Your Mr-Glass Sliding & Patio Doors Is Failing

• The door takes real effort to move. Roller bearings wear flat on one side, and the wheel stops rolling and starts sliding through the track. That friction grinds the aluminum track thinner every time the door moves.
• A grinding or metallic scraping sound when you open or close. This is usually a roller wheel that has seized and is now being dragged across the track. The sound means the track is being damaged by the passage, not just the roller.
• The door drops or sags noticeably on one side. The roller assembly has likely broken or the adjustment screw has stripped. A sagging panel drags the bottom rail against the track and will eventually cut into the weatherstripping channel.
• Visible corrosion or white pitting on the aluminum track. Florida humidity and salt air cause electrolytic corrosion where steel roller brackets meet aluminum track. Once the track is pitted, new rollers will not fix the problem completely.
• The latch or handle won’t engage, or the door locks but can be lifted out of the track. Worn keeper pins and misaligned rollers let the panel rock out of the locked position. A door that can be lifted out while locked is a door that’s not doing its job.

Replacement Cost & What’s Included

In Boca Raton, expect to pay $160 to $240 for a standard double-roller replacement on a Mr-Glass slider, including the parts and the labor to pull the panel, install the new rollers, and adjust the door for a square reveal. A complete handle and lock set runs $120 to $210 installed. A full track replacement and door re-alignment, where we remove corrosion, install a new track, and reset the rollers, typically falls between $330 and $490 depending on the door size and condition of the frame.

What drives the price is the condition of the track. If the rollers failed early and the track is clean, you’re at the low end. If the door has been grinding for a year, the track may need replacement, which means more labor and material. We show you the numbers on paper before we start, and the price we quote is the price you pay. No change orders, no surprise line items.

Every Mr-Glass parts replacement is backed by our Done Right Promise and The Keystone Standard: both manufacturer warranty layers registered in writing, durations stated, before the truck leaves the driveway. If it isn’t square and it isn’t sealed, it isn’t done.

DIY or Call Us?

Sliding door roller replacement is one of those jobs that looks easy in a video and fights you in real life. The panel is heavy, typically 90 to 140 pounds for a Mr-Glass glass slider, and lifting it out of the track without dropping it requires two people and the right shimming. The adjustment screws on the roller assembly are accessible, but if you misadjust them, the door will bind and you’ll wear out the new rollers in months.

There is one thing we tell every Boca Raton owner to check themselves: the track. Vacuum it, wipe it down, and look for visible pitting or cracks. If the track is clean and the door still fights you, it’s the rollers, and that is a job worth having done by someone who does this every week.

What goes wrong with DIY is almost always the alignment. A door that is out of square by a quarter inch will chew up new rollers quickly, and then you are back where you started. Our approach is different: Dale Kessler grew up in the Boca Teeca neighborhood of Boca Raton, and his father spent weekends replacing jalousie windows in every house on the block. After finishing his glazing and fenestration coursework at Palm Beach State College, Dale spent more than two decades measuring, setting, and sealing windows and doors across Palm Beach County. He started TruePane because he watched too many homeowners get handed a low bid and a loose frame, and he decided someone in this market ought to stand behind the work with more than a handshake.

Call (561) 264-1337 and we’ll get you the right part on the first visit, not after three callbacks.

FAQs

Get Your Mr-Glass Door Rolling Again

We serve Boca Raton and the surrounding communities with the same standard on every job: a square frame, a sealed track, and a door that rolls the way it should. Our team includes background-checked, uniformed technicians who measure every opening twice, quote manufacturer lines side by side on paper, and register both warranty layers before the truck leaves the driveway. A live person answers the phone 24 hours a day, 7 days a week, and we’ll be there when we say. Call (561) 264-1337 to schedule your free estimate.

Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving Boca Raton and nearby areas.