Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterMr-Glass Custom & Geometric Windows in Boca Raton: What to Know First
We provide independent Mr-Glass custom and geometric window repair and replacement throughout Boca Raton, with most service calls completed in a single visit. A typical Mr-Glass specialty window job in this market runs between $425 and $2,800 depending on whether we’re replacing a failed seal, rebuilding a curved sash, or fabricating a full geometric unit. We are not a Mr-Glass dealer or authorized service center, but we’ve worked on enough of their shaped and oversized units in Palm Beach County to know exactly what fails, why it fails, and what holds up in this salt-and-humidity climate.
This page is for homeowners who own a Mr-Glass product, need custom or geometric window work, and want a straight answer on cost, timeline, and whether the frame is worth saving. If you’d rather talk it through, call us at (561) 264-1337.
How Mr-Glass Products Fail - and How We Fix Them
Mr-Glass builds a lot of shaped and oversized units for high-end South Florida homes. Quality varies by series, and we see the same failure patterns repeat across Boca Raton neighborhoods from Royal Palm Yacht & Country Club to Boca Bridges. Here’s what we actually find on service calls:
- Curved and radius units losing their gas fill at the corner welds. Mr-Glass arched windows and radius tops tend to develop seal failure where the curved glass meets the frame, usually within 8 to 12 years in coastal air. The symptom is a fog patch that starts at the bottom corner and creeps inward. We replace the insulated glass unit and set the new one in a bed of fresh structural sealant, not just foam tape.
- Geometric fixed units with sagging or out-of-square frames. Large trapezoid and triangle windows carry a lot of glass weight. If the original rough opening had any flex, you’ll see cracking at the drywall corners and a sash that binds on one side. We remove the unit, check the rough opening with a level and square, and shim the frame back to true before re-setting it.
- Oversized octagon and circle-top units with broken point connections. Mr-Glass circle-top and octagon windows often use interior muntin grids clipped into place. The clips are plastic, and in a decade of Florida sun they get brittle. The grid falls out of alignment and rattles every time a door closes. We replace the clips with metal alternatives where the profile allows, and re-align the grid to factory spacing.
- Hardware on operable geometric units that was never right for the weight. We’ve opened up Mr-Glass casement and awning windows in custom shapes where the operator mechanism is undersized for the sash. Cranking gets stiff, then strips. We replace the hardware with a heavier-rated operator and adjust the hinge track so the sash seats square against the weatherstrip.
- Impact-rated shaped units with delaminating laminate at the millwork seam. On Mr-Glass impact windows in custom shapes, the laminated safety glass interlayer can begin separating where the glass was cut to a sharp angle. You’ll notice a slight haze at the corner that never cleans off. There is no field fix for delamination. We quote a replacement IGU with proper edge clearance so the new unit doesn’t repeat the same failure.
Our Mr-Glass Custom & Geometric Windows Process
- 1
The call. You reach us at (561) 264-1337. A live person answers and asks basic questions about the window: shape, age, symptoms, and whether it’s impact-rated. We schedule a service visit around your calendar, and we show up on time, in uniform, with a background-checked tech.
- 2
The diagnostic. Our technician measures the unit twice, checks the frame for square and plumb, records the glass type and thickness, and photographs every detail. On a Mr-Glass job, we also check the original mounting method, because some of their older custom units were set with methods that don’t hold up in this climate.
- 3
The parts decision. If the glass is still available through Mr-Glass’s distribution network, we quote OEM replacement. If it’s discontinued or the lead time is six months, we quote a quality aftermarket IGU from a fabricator we’ve used for over a decade. We show you both options on paper, with prices and real lead times, side by side.
- 4
The work. We remove the failed unit without damaging the frame or the surrounding stucco and drywall. The new glass is set, shimmed, and sealed. For geometric and oversized units, we spend extra time on the structural sealant bead, because that’s where most warranty failures begin.
- 5
The test and the paper. We operate the window, check the seal, confirm the frame is square, and clean the glass and the worksite. Before we leave, you get written documentation of both warranty layers and their durations under The Keystone Standard.
What Mr-Glass Custom & Geometric Windows Costs in Boca Raton
Here’s what we typically quote for Mr-Glass custom and geometric window work in this market. Every job is quoted upfront, in writing, with no surprise line items on the bill. You’ll know the price before we start, and we don’t change it mid-job.
Mr-Glass Custom & Geometric Window Pricing
| Job Type | Typical Range |
|---|---|
| Seal failure repair on a shaped IGU (circle-top, radius, trapezoid) | $425 - $950 |
| Replacement hardware for operable geometric window (casement, awning) | $180 - $420 |
| Frame re-square and re-set on an oversized fixed unit | $600 - $1,400 |
| Full replacement of a custom geometric window (impact-rated) | $1,800 - $2,800+ |
| Complete re-glaze of a large arch or circle-top unit | $1,200 - $2,200 |
What moves the price: glass thickness and impact rating, lead time on the IGU, whether the frame needs to be rebuilt, and access. Third-story arch windows on a ladder cost more than a ground-floor circle-top. Call (561) 264-1337 for an exact quote. Estimates are free, and we mean that the same way we mean everything else: no fine print.
Why Boca Raton Homeowners Call TruePane Windows & Doors for Mr-Glass Work
We are not the cheapest bid in the room, and we don’t try to be. We are the last call you should need to make on a Mr-Glass window. The Keystone Standard backs every job: both manufacturer warranty layers registered in writing before our truck leaves your driveway, durations stated, workmanship guaranteed for 90 days under our Done Right Promise. If it’s not done right, we make it right without paperwork fights and without arguing.
We’ve been serving local communities since 2008, founded in this craft tradition by Dale Kessler. Our techs are background-checked, uniformed, and trained to work in your home the way they’d work in their own mother’s. When your Mr-Glass unit is beyond practical repair, we can quote replacement options from PGT, CGI, CWS, and ES Windows, because we’re an authorized installer for more than a dozen manufacturer lines. Side-by-side quotes on paper, so you see exactly what you’re buying.
Frequently Asked Questions
In most cases, no. As an independent Mr-Glass service provider, we perform repairs that do not void the original manufacturer warranty when we use OEM or equivalent-quality parts and follow the original installation method. We document every repair and register warranty layers in writing. If your unit is still under Mr-Glass’s warranty, we’ll tell you, and we’ll walk you through what the manufacturer will cover versus what falls to you. Call (561) 264-1337 and we’ll look up your specific situation.
Yes, in nearly every case. We pull the original glass spec off the window’s edge marking or the frame’s manufacturing label, then match tint, thickness, low-E coating, and impact rating through the same fabricators that supply much of the South Florida replacement market. The one honest exception is very old Mr-Glass units with discontinued coatings. If that happens, we’ll tell you before ordering and show you the closest available match. Call us for a free evaluation.
Most seal failures, hardware replacements, and re-squares on Mr-Glass custom and geometric windows are completed in a single visit, usually within two to four hours. If we need to order a custom IGU, the lead time is typically two to three weeks depending on glass type and impact rating. We give you the timeline in writing before we order anything. Call (561) 264-1337 and we’ll give you an honest estimate over the phone.
For seal failure or hardware problems on a frame that’s still square and solid, repair is almost always the better financial decision. For delaminated impact glass or a frame that’s twisted from years of heat and wind load, replacement is the only fix that holds. We quote both options on paper and let you decide. If we think a repair won’t last, we tell you that too. Call (561) 264-1337 for a straight answer, not a sales pitch.
Custom and geometric work is exactly what we do. Arches, circle-tops, radius corners, trapezoids, triangles, octagons, oversized openings. Dale Kessler’s father spent weekend after weekend replacing jalousie windows in the Boca Teeca neighborhood of Boca Raton, and the lesson stuck: if it isn’t square and it isn’t sealed, it isn’t done. We measure every opening twice and we don’t set a shaped unit until the frame reads true on the level. Call (561) 264-1337 and tell us what shape you’re dealing with.
Get Your Mr-Glass Window Done Right in Boca Raton
We’ve spent years earning a reputation for square frames, clean sills, and installs that hold through hurricane season. If your Mr-Glass custom or geometric window is fogged, binding, leaking, or just not closing the way it used to, call us at (561) 264-1337 for a free estimate. A live person answers every call. We’ll set a time, show up, measure twice, and put the number in writing before any work begins.
Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving Boca Raton and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.