Andersen Window Installation Nationwide | TruePane Windows & Doors

Andersen Window Installation in Boca Raton: What to Know First

Andersen window installation in Boca Raton typically runs $180 to $340 per window for labor on a straightforward replacement, with full-frame tear-outs running higher and multi-window projects priced per opening. TruePane Windows & Doors is an independent Andersen service provider, and most Andersen jobs are completed in a single visit. We are not affiliated with Andersen, and we do not pretend to be. The page that follows is written for homeowners who own Andersen windows, intend to keep this house, and want the work done right the first time. Call (561) 264-1337 for a free estimate.

Call (561) 264-1337

How Andersen Products Fail - and How We Fix Them

Andersen makes a good window. If they did not, we would not have spent four decades setting them in Boca Raton homes. But every manufacturer line has weak points, and Andersen’s show up in specific ways under salt air and Florida sun. Here is what we see.

• 400 Series Tilt-Wash sashes lose their seal at the glazing bead. The vinyl liner and the wood sash expand at different rates in humid coastal air. The result is a window that fogs at the edges, not the center, and a homeowner who blames the glass when the real problem is the bead. We reglaze, reseat, and seal, using OEM Andersen sealant where it matters and a better aftermarket bead when the factory part is the reason it failed twice.
• 200 Series Perma-Shield casement cranks bind in July. The roto gear inside the operator is plastic, and after a decade of salt air it grinds itself smooth. The window will not close square, and forcing it bends the arm. We replace the operator with the metal-gear version and realign the sash so it closes tight without a fight.
• Narroline double-hung balances fatigue on the coast. The block-and-tackle balance cords are rated for cycles, not for twenty years of damp, salty mornings. When one side lets go, the sash drops hard and the homeowner thinks the frame is shot. It is not. We replace both balances, never just the broken side, so the sash lifts evenly.
• A-Series and 400 Series wood frames rot at the lower sash corner on east-facing exposures. Morning sun bakes the condensation off, then afternoon rain drives into the same joint. What starts as a soft corner becomes a frame that will not hold a screw. On windows worth saving, we cut out the rot, treat, fill with a marine-grade epoxy, and re-set the sash. On windows past saving, we say so plainly and quote a replacement.
• Frenchwood hinged patio doors sag at the hinge side over time. The weight of the panel pulls the top hinge, the reveal goes uneven, and the door starts dragging. It is not a level floor; it is a worn hinge. We re-hang the panel, shim the jamb square, and adjust the threshold so the door closes with one finger.

The point is this: Andersen failures are rarely mysterious. They are specific, they repeat, and they have fixes that hold. The trick is knowing which fix applies.

Our Andersen Window Installation Process

Every Andersen job follows the same sequence. No shortcuts, no surprises.

1. 1
   Measure the opening twice. We measure the rough opening, the existing sash, and the diagonal square before we quote anything. An out-of-true frame changes the entire plan.
2. 2
   Diagnose before we unscrew anything. We identify the failure mode and show you the exact part or seal that let go. You see the problem before we touch it.
3. 3
   Present OEM and aftermarket options on paper. Where factory parts make sense, we quote them. Where a better aftermarket part exists, we quote that too, side by side, with the honest trade-off spelled out. You decide.
4. 4
   Set, level, shim, and seal. Every unit goes in square to the rough opening and sealed against water intrusion at the flange and sill. No foam-and-fingers work.
5. 5
   Test operation before we clean up. We open and close every sash, check the reveals, and run a water test at the sill. If something is not right, we fix it before you see it.
6. 6
   Register the warranty layers in writing. Both manufacturer warranty layers, stated durations, on paper. The Keystone Standard. Before the truck leaves the driveway.

Then we clean the sill, sweep the drop cloth, and hand you the paperwork. Dale Kessler keeps one rule on the whiteboard in the shop, and it governs every one of those steps: if it isn’t square and it isn’t sealed, it isn’t done.

What Andersen Window Installation Costs in Boca Raton

Straight Andersen window installation labor in Boca Raton runs $180 to $340 per window, depending on access, frame condition, and whether we are doing a sash replacement or a full frame tear-out. Here is a realistic line-item view.

• Single hung or double hung sash replacement: $180 to $280 per window
• Casement or awning window re-set and reseal: $220 to $340 per window
• Full-frame replacement with trim: $380 to $650 per window
• Frenchwood hinged patio door rehang and adjust: $450 to $750 per panel
• Rot repair at a sash corner before reinstallation: $85 to $190

What moves the price: second-story access, rotted rough framing, out-of-square openings that need shimming back to true, and whether the existing flashing can be reused. Our quotes are fixed. The number on the written estimate is the number on the invoice. No change orders once work starts unless you add scope, and even then we hand you the new price before we pick up the tool. Call (561) 264-1337 for a free estimate.

Why Boca Raton Homeowners Call TruePane Windows & Doors for Andersen Work

We have been setting windows in Palm Beach County since 2008. Dale Kessler grew up in the Boca Teeca neighborhood, and learned the trade from a father who spent weekends replacing jalousie windows and refused to call it a hobby. TruePane was founded in 2008 on a simple observation: too many homeowners got handed a low bid and a loose frame, and nobody in this market was standing behind the work with more than a handshake.

Every job carries the Done Right Promise. If the install is not right, we make it right, no paperwork fight and no fine print that covers neither. Both manufacturer warranty layers are registered in writing before the truck leaves the driveway. And when you call, a live person answers, 24/7. Not a voicemail tree, not a callback form. A person.

We are an authorized installer for more than a dozen lines including, PGT, and CGI, which means we quote manufacturer lines side by side on paper so you see exactly what you are buying. No mystery, no pressure. Just a square deal.

FAQs