Andersen Sliding & Patio Doors Nationwide | TruePane Windows & Doors

Andersen Sliding & Patio Doors: The Boca Raton Owner’s Guide

We stock rollers, handles, latch sets, weatherstripping, and replacement panels for Andersen sliding and patio doors, and we install them across Boca Raton. Installed part replacement typically runs $165 to $480 depending on the component, the series, and whether the door needs realignment. Most Andersen slider repairs are single-visit jobs. You usually discover the failure on a humid morning when the door drags against the track, or when the handle no longer pulls the latch back far enough to open.

Call (561) 264-1337

Key Takeaways

• Andersen sliding door parts are series-specific. A 200 Series roller will not seat in a 400 Series door. Bring the glass etching or the original paperwork, or let us read the label off the frame.
• We stock common Andersen rollers, latches, handles, and weatherstripping on the truck. Obscure trim parts are sourced within days through our manufacturer channels.
• Installed pricing is fixed before work begins. You see the line item. No change orders on a simple parts replacement.
• We register both warranty layers in writing. The part carries its manufacturer warranty; our labor carries the Done Right Promise.

Which Andersen Models This Applies To

Andersen builds sliding patio doors under a few distinct families: the 200 Series (wood interior, vinyl exterior), 400 Series (wood interior and exterior with a range of cladding options), and the A-Series (architectural line with deeper frames). Parts do not interchange across series. The 200 Series roller is a different diameter and a different housing shape than the 400 Series roller, and a 400 Series latch set will bind in a 200 Series door. We also field calls for the E-Series and the older Narroline and Frenchwood sliders still hanging in plenty of Boca Raton homes built in the 1980s and 1990s. To identify your door, look at the lower corner of the operable panel, inside the frame channel. Andersen etches the series and sometimes the manufacture date into the glass. If the etching has worn off or you cannot find it, we read the hardware: roller housing dimensions and latch geometry get us to the right series within minutes. We default to OEM Andersen parts on anything still in production. When a series is discontinued and the OEM part is no longer available, we will tell you that plainly and quote a quality aftermarket equivalent only if we have installed it before and stood behind it.

Signs Your Andersen Sliding & Patio Doors Is Failing

• The door drags or scrapes when you slide it. Roller bearings wear out, or the roller housings fill with sand, salt haze, and dust. In Boca Raton, the fine beach sand off the barrier islands works its way into the track and grinds the bearings down faster than anyone expects.
• The handle turns but the latch barely moves. Andersen latch mechanisms use a spring-loaded internal hook. The spring fatigues over time, especially on doors that face morning sun and afternoon storms. The handle feels loose and the door no longer seats properly against the weatherstripping.
• The door leaks light or air around the edges. Weatherstripping compresses, shrinks, and hardens. The felt-pile strips on the vertical edges flatten after a decade. In a humid climate, the result is a door that lets conditioned air out and damp air in.
• The door locks, but only after you lift or push down on the handle. That is the latch alignment failing. The sliding panel has dropped slightly, or the keeper on the jamb has shifted. Lifting the handle compensates for a misalignment that should be corrected, not lived with.
• The panel skips, hangs, or jumps the track. A roller has seized and the panel rides on bare metal against the track. The complaint we hear most in Boca Raton is that the door “bounces” mid-slide. That is a flattened roller with a dead bearing.

Replacement Cost & What’s Included

In Boca Raton, Andersen slider parts replacement runs between $165 and $480 installed. A roller swap on a 200 Series door is on the lower end. A full roller replacement on both panels of a 400 Series door, with realignment and new weatherstripping, lands in the $300 to $480 range. Handles and latch sets run $180 to $340 depending on the finish and whether we are replacing the interior and exterior hardware together. You get a written line-item quote before any work starts. The quote states the part, the series, the price, and the labor. Nothing gets added on the bill at the end. If a door comes out of alignment during the repair, we true the track and the rollers before we leave. Part warranties are registered in writing with the manufacturer. Our workmanship carries the Done Right Promise: if the door is not sliding right, we come back and fix it. No paper shuffle.

DIY or Call Us?

Andersen sliding doors are not spring-loaded like a garage door, so there is no high-tension component that will take your hand off. That said, the panel on a 400 Series slider weighs between 120 and 180 pounds, and removing it means lifting it out of a track while balancing on one knee. If the panel drops, the glass does not care about your good intentions. Here is the honest split. You can safely clean the track, inspect the roller housings for visible flat spots, and test the latch by sliding the handle slowly with the door open. What you should not do is pull the panel out to replace rollers yourself on a door that faces a second-story balcony or weighs more than you do. We have been called to fix more DIY roller jobs where the owner dropped a panel, cracked a corner, or sheared a roller housing trying to force it. If you can manage the door and you have the exact OEM part, it is a possible Saturday project. If you want it sliding like it did in 1998, call us at (561) 264-1337 and we will square it up and seal it down.

FAQs