Andersen Door Installation Nationwide | TruePane Windows & Doors

Andersen Door Installation in Boca Raton: What to Know First

Andersen door installation in Boca Raton typically runs $1,200 to $4,800 depending on the door line, the condition of the existing opening, and whether you’re replacing a slab or the full frame. We’re an independent Andersen service provider in Boca Raton, not a manufacturer affiliate, and we schedule most single-door installs within five to seven business days. The honest posture is this: if the rough opening is square and sealed, an Andersen door goes in clean. If it’s not, the job costs more and takes longer, and we’ll tell you why before we touch it. This page is for Boca Raton homeowners who already own an Andersen door, or are buying one, and want it installed by people who understand what those doors need in this climate. Call (561) 264-1337 to talk it through.

Call (561) 264-1337

How Andersen Products Fail - and How We Fix Them

• Andersen 400 Series French doors lose their weatherstrip edge after a few hurricane seasons. The compression weatherstrip on the inactive panel gets brittle under Boca Raton’s salt air and UV load, which lets humidity creep into the slab edge. We pull the panel, inspect the sill cap, and replace the weatherstrip with the proper Andersen profile, not a universal squeeze-in substitute. A door that seals tight at the threshold and the head stops wicking moisture into the core.
• Andersen A-Series entry doors are the ones we see binding in July. The engineered wood stiles and rails on A-Series doors swell slightly with summer humidity, and if the original installer set the reveal at the minimum, the door starts dragging on the latch side. The fix is a hinge adjustment and sometimes a hair of stile planing, done carefully so the factory finish stays intact. Most of the time the door is fine; the original install was just too tight for a Boca summer.
• Andersen Storm Doors with retractable screens develop a snap-in track issue we see every month. The screen track on the 3000 Series storm door gets worked loose by daily use until the screen pops out of its channel. We remove the track, reset the tension, and re-seat it with fresh fasteners, which takes about 45 minutes. The glass itself is usually fine; it’s the track hardware that gives up first.
• Andersen 200 Series gliding patio doors are the quiet failure in older Boca homes. The rollers on the 200 Series sit in an exposed bottom track, and after a decade of sand and shell grit working its way in, the rollers flat-spot. The door still slides, but it takes a shoulder shove. We replace the roller assembly with the current Andersen part and deep-clean the track so the door glides with two fingers. This is also when we check the sill for hairline cracks, which is a separate conversation if we find one.
• Andersen E-Series doors with factory-finished exteriors need touch-up discipline, not repainting. The E-Series is the high-end line, and its aluminum-clad exterior holds up better than most, but an install that nicks the cladding and leaves bare aluminum starts a corrosion line that spreads. On every E-Series job we carry factory-match touch-up and treat any bare edges before we call the door finished. It’s a ten-minute detail that saves an owner from looking at a rust trail in three years.

Our Andersen Door Installation Process

Here’s how a standard Andersen door installation runs with our crew, from the first call to the last sweep of the entry.

1. 1
   Call and talk to a person. You reach us at (561) 264-1337. We ask about your door, the rough age of the house, and what you’re seeing. No forms, no waiting on a call center.
2. 2
   Site measure and honest quote. We measure every opening twice, as Dale Kessler has done since he was learning glazing at Palm Beach State College. You get a written line-item quote before any work starts.
3. 3
   Parts decision on the table. If we’re installing a new Andersen door, great. If we’re repairing one, we lay out OEM versus quality aftermarket options with prices, so you choose with full information.
4. 4
   The install. Our uniformed, background-checked techs set the frame square, shim it true, and seal it for Boca Raton’s rain and humidity. If the pane is not true, the job is not done.
5. 5
   The test and the paperwork. We open and close the door, check the weatherstripping, and verify the hardware. Before the truck leaves your driveway, both manufacturer warranty layers are registered in writing, with durations stated.
6. 6
   The Done Right Promise. If something is not right after we leave, we come back and make it right. No paperwork fights, no arguing. That’s The Keystone Standard.

What Andersen Door Installation Costs in Boca Raton

Here are real price ranges for common Andersen scenarios in Boca Raton, based on what we’ve quoted across the city:

• Single Andersen entry door replacement, slab only: $1,200 to $2,400. Assumes the existing frame is square and sound.
• Full-frame Andersen entry door installation, including new frame and casing: $2,200 to $3,800. More if the rough opening needs correction.
• Andersen French door or double door installation, full replacement: $2,800 to $4,800 per opening. Hardware and finishing options move this number.
• Andersen storm door installation: $450 to $1,100 including hardware and trim, depending on the series and retractable screen.
• Andersen patio or gliding door replacement: $1,800 to $3,500, with the price moving based on opening size and whether the sill needs rework.

What moves the price: whether the rough opening is square, whether the sill has water damage, whether we’re matching an existing trim profile, and whether the door needs factory-look finishing. Boca Raton’s humidity means sill rot is the wild card more often than people expect. Call (561) 264-1337 for an exact quote on your opening. Estimates are free, and the number we give you is the number you pay.

Why Boca Raton Homeowners Call TruePane Windows & Doors for Andersen Work

We’ve been doing this in South Florida since 2008, and the reason people call us for Andersen work is not because we’re the cheapest, because we’re not. It’s because we do it right the first time and stand behind it in writing. Dale Kessler started this company after watching too many homeowners accept a low bid and a frame that wasn’t square. We’re an authorized installer for more than a dozen lines, including, PGT, and CGI, which matters when you want side-by-side quotes on paper and no brand loyalty color the recommendation. Our techs wear uniforms, pass background checks, and treat your entryway like it’s their own mother’s front door. A live person answers the phone 24 hours a day, seven days a week. We’ll be there when we say. And if it isn’t square and it isn’t sealed, it isn’t done. That’s the rule.

FAQs